My cluster illumination was not working but everything else controlled by the switch worked fine. I finally got around to replacing the switch today. The cluster illumination will not turn off now. Ignition off , key out , cluster stays illuminated , and the dimmer portion of the switch gets...
When the switch is pulled out the first click it immediately blows the fuse. Headlights still work but no running lights. I replaced the switch , traced wires , checked tail lights , disconnected the power side of the running board lights and the visor lights , disconnected the trans temp gauge...
I am going to attempt to recharge my AC. I had to open up the system when I swapped engines. I don't think any oil leaked out so I think I should be able to just test and recharge..? Does anyone know if the Harbor Freight AC gauge set works with r12??
I have a banks transcommand on my e4od. I've had e4od's in the past and I expected this one to shift firmer.. But it actually shifts pretty mushy. It doesn't slip , it just has extremely soft shifts. The trans is a low mile reman. The FIPL is on the higher side of adjustment ( 1.2@idle and...
I need some engine lift eye brackets. I use to have a pile of them but I gave it all away when I thought I was getting out of the IDI world. I'm pulling an engine and it doesn't have any. I'm assuming they were removed for the turbo kit. Does anyone have some??
I can never seem to go more than a year or so without an IDI before I drag a new one home. I've been looking for another one for awhile and finally found the one I wanted!
Specs :
1992 F250 4x4 ext cab
7.3l with a Banks turbo and full exhaust
New e4od with Banks transcommand
3g alternator...
I have an 85 f250 6.9 extended cab with a 2wd c6. The gear vendors unit is bad so I want to just eliminate it. I need a c6 tail housing and stock driveshaft.
I am located in Medford,OR but can travel or possibly pay shipping.
I just picked up a 2wd bullnose. It has a c6 and J type gear vendors. Reverse works fine, but it shudders in forward gears and doesn't like to move. The trans was recently rebuilt and is just out of it's warranty. The first thing I noticed was the wires to the GV were broken at the solenoid ...
Hey guys. I just got the Holley red hooked up and have a question. I ended up mounting it on the back side of my coolant filter ( which is mounted off the filter head ) because it literally fit perfect on the same mount/bolts. My only concern is the vibrations from the engine. Do you guys think...
This is probably a stupid question.. I'm installing a Holley red . I have a few spare starter relays and I was wondering if they can be used for constant duty? Or do I need a different type of relay to power the pump?
I have a 55 gph fuge for sale. It comes with everything in the link below. I filtered 1,000 gallons with it and had zero issues. At the time diesel was over $4.00 so it more than payed for itself ! It is in good condition and works great. Only selling because im getting out of the idi scene...
My 88' Centurion has a fiberglass sun visor. The problem is it was mounted with self tapping screws and the holes over time became loose/stripped out. Does anyone have a picture of the interior roof without a headliner ? I'm wondering if I can just replace the screws with a bolt and nut from the...
Hey guys. I'm in the process of pulling a 6.9 to replace head gaskets. It has an ats 085 kit. I can't get the engine out with the turbo kit installed, and I cannot remove the turbo. I've tried penetrating oil, heat, breaker bar.. The down pipe and flange bolts won't budge. Any ideas?
So I just got my truck back on the road after doing head gaskets. It runs great. Yesterday I turned the truck off, and when I went to start it again the starter wasn't working. The starter gear pops out but doesn't spin. I pulled the starter and bench tested and it works fine, tossed it back in...
I'm wondering if the port on top , to the right ( the one that's usually plugged ) is an inlet or outlet? My truck has a hose running from it to the side of the block , near the starter. I'm installing a coolant filter and figured I might as well just use that hose since it currently has no...
I need a set of sending Units for my '88 f350 diesel. Don't have the cash for new ones right now , so looking for used/Working condition. Anyone have some?
Man I cannot get these brakes to firm up. Every bleed point has a solid stream of fluid , zero air. But it just won't firm up. New master cylinder.. Any ideas?
Looking at buying a trailer.. It's a tilt deck equipment trailer. I just noticed that in one of the pictures it looks like the axles are way far forward. Am I seeing things or is this normal? I don't know much about trailers but from what I do know the axles are usually centered or towards the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.